Products Details

image
image
image

AirCurve10 VAuto BiPAP

৳0.00
ResMed AirCurve10 VAuto BiPAP Machine is an auto-adjusting bilevel machine that uses the comfort of both the AutoSet algorithm and Easy-Breathe waveform in its VAuto algorithm to treat obstructive sleep apnea patients who can benefit from greater pressure support. The AirCurve 10 VAuto adjusts the baseline pressure to hold the airway open while maintaining a fixed pressure support.
Operating Mode S, VAuto, CPAP
Housing Construction Flame retardant engineering thermoplastic
Supplemental Oxygen Maximum flow: 15 L/min (CPAP, S); 4 L/min (VAuto)
Standard Air Filter Material: Polyester non woven fibre, Average arrestance: >75% for -7 micron dust
Hypoallergenic Air Filter Material: Acrylic and polypropylene fibres in a polypropylene carrier, Efficiency: >98% for:- 7-8 micron dust; >80% for:- 0.5 micron dust
Air Outlet 22 mm
Water Capacity To maximum fill line 380 mL
Typical Power Consumption 53 W (57 VA)
Peak Power Consumption 104 W (108 VA)
Maximum Single Fault Steady Pressure Device will shut down in the presence of a single fault if the steady state pressure exceeds:30 cm H2O (30 hPa) for more than 6 sec or 40 cm H2O (40 hPa) for more than 1 sec
Wireless Module Technology used:4G, 2G. It is recommended that the device is a minimum distance of 2 cm from the body during operation. Not applicable to masks, tubes or accessories. Technology may not be available in all regions

Product Details of ResMed AirCurve10 VAuto BiPAP Machine:

Brand ResMed
Model AirCurve 10 Vauto
Usage/Application Hospitals & Personal Use
Pressure Range (cm H2O) S, VAuto: 2 to 25 cm H2O (2 to 25 hPa); CPAP: 4 to 20 cm H2O (4 to 20 hPa)
Ramp Rate (mins) 5 to 45 minutes

 

Additional Details

Pressure Sensor Internally located at device outlet, analogue gauge pressure type, -5 to +45 cm H2O (-5 to +45 hPa)
Power Supply Unit 90 W, AC input range:100–240 V, 50–60 Hz 1.0–1.5 A, Class II 115 V, 400 Hz 1.5 A, Class II (nominal for aircraft use); DC output:24 V 3.75 A
Flow Sensor Internally located at device inlet, digital mass flow type, -70 to +180 L/min

 

General System

Weight With Humidifier 1248 gm
Dimensions 205 x 150 x 116 mm (without humidifier), 255 x 150 x 116 gm (with humidifier)
Warranty 2 Years

 

Comfort Features

Operating Temperature +5°C to +35°C Note: The air flow for breathing produced by this therapy device can be higher than the temperature of the room. Under extreme ambient temperature conditions (40°C) the device remains safe.
Operating Altitude Sea level to 2591 m; air pressure range 1013 hPa to 738 hPa

 

Sound

Pressure Level Measured According to EN ISO 17510-1:2009 (CPAP mode); SlimLine: 26.6 dBA with uncertainty of 2 dBA, Standard: 26.6 dBA with uncertainty of 2 dBA
Power Level Measured According to EN ISO 17510-1:2009 (CPAP mode); SlimLine: 34.6 dBA with uncertainty of 2 dBA, Standard: 34.6 dBA with uncertainty of 2 dBA

 

Features of ResMed AirCurve10 VAuto BiPAP Machine:

  • Easy-Comfort Breathe Technology
  • Consistent Humidification
  • Built-in Ambient Light Sensor
  • Continuous Leak Management
  • Quiet Easy-Breathe Motor
  • Climate Control